When it comes to improving your golf game, you can spend thousands of dollars buying the latest titanium-induced, PGA player-promoted golf clubs; taking private lessons from the local "I used to be on the Tour" pro; or trying every slice-correcting, swing-speed-estimating, GPS-distance-guessing gadget. But, in the end, it’s about getting that little white sphere to go where you intended it to go.
Don't worry, there are many very smart people trying to help you by designing the ultimate golf ball. Of course, they are also after a slice of this billion dollar industry, as any technological advancement that can grab a few more market share points is worth the investment.
The challenge for golf ball manufacturers is to design a better performing ball within the constraints set by United States Golf Association. The USGA enforces limits on the size, weight and initial performance characteristics in an attempt to keep the playing field somewhat level. Every "sanctioned" golf ball must weigh less than 1.62 ounces with a diameter smaller than 1.68 inches. It also must have a similar initial velocity when hit with a metal striker, and rebound at the same angle and speed when hit against a metal block. So, what is left to tinker with? Manufacturers have focused on the internal materials in the ball and its cover design.
Today's balls have 2, 3 or 4 layers of different internal polymer materials to be able to respond differently when hit with a driver versus, say, a wedge. When hit with a driver at much higher swing speed, the energy transfer goes all the way to the core by compressing ball, reducing backspin. During a slower swing with a club that has more angle loft, the energy stays closer to the surface of the ball and allows the grooves of the club to grab onto the ball's cover producing more spin. When driving the ball off of the tee, the preference is more distance and less loft, so a lower backspin is required. For closer shots, more backspin and control are needed.
Which brings us to the cover of the ball and all of the design possibilities. Two forces affect the flight and distance of flying spheres, gravity and aerodynamics. Eventually, gravity wins once the momentum of the ball is slowed by the aerodynamic drag. Since all golf clubs have some angular loft to their clubface, the struck ball will have backspin. As explained by the Magnus Force effect, the air pressure will be lower on the top of the ball since that side is moving slower relative to the air around it. This creates lift as the ball will go in the direction of the lower air pressure. Counteracting this lift is the friction or drag the ball experiences while flying through the air.
Think about a boat moving through water. At the front of the boat, the water moves smoothly around the sides of the boat, but eventually separates from the boat on the back side. This leaves behind a turbulent wake where the water is agitated and creates a lower pressure area. The larger the wake, the more drag is created. A ball in flight has the same properties.
The secret then is how to reduce this wake behind the ball. Enter the infamous golf ball dimples. Dimples on a golf ball create a thin turbulent boundary layer of air molecules that sticks to the ball's contour longer than on a smooth ball. This allows the flowing air to follow the ball's surface farther around the back of the ball, which decreases the size of the wake. In fact, research has shown that a dimpled ball travels about twice as far as a smooth ball.
So, the design competition comes down to perfecting the dimple, since not all dimples are created equal! The number, size and shape can have a dramatic impact on performance. Typically, today's balls have 300-500 spherically shaped dimples, each with a depth of about .010 inch. However, varying just the depth by .001 inch can have dramatic effects on the ball's flight.
Regarding shape, these traditional round dimple patterns cover up to 86 percent of the surface of the golf ball. To create better coverage, Callaway Golf's HX ball uses hexagon shaped dimples that can create a denser lattice of dimples leaving fewer flat spots. Creating just the right design has traditionally been a trial-and-error process of creating a prototype then testing in a wind tunnel. The next step is to begin the quest for the ultimate dimple.
In the meantime, when someone asks you, "What's your handicap?" you can confidently tell them, "Well, my golf ball's design does not optimize its drag coefficient which results in a lower loft and spin rate from its poor aerodynamics."